TY - JOUR
T1 - Investigation of properties of polyethylene/clay nanocomposites prepared by new in situ Ziegler-Natta catalyst
AU - Nikkhah, S. Javan
AU - Ramazani, A.
AU - Baniasadi, H.
AU - Tavakolzadeh, F.
PY - 2009/8
Y1 - 2009/8
N2 - This paper is devoted to investigation of morphological and physical-mechanical properties of polyethylene (PE)/clay nanocomposites prepared via in situ polymerization method using bi-supported Ziegler-Natta catalyst. Bentonite type clay and MgCl2 (ethoxide type) were used as the support of TiCl4. Catalyst support and polymerization process have been done in slurry phase using Triisobutylaluminum as the co-catalyst. The microstructure of the nanocomposites was examined by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD and TEM indicated that almost fully exfoliated PE/clay nanocomposites were produced successfully using this method. According to permeability measurements, it was found that oxygen permeability values of the nanocomposite samples prepared with in situ polymerization method were dropped more than 200% introducing only 1 wt% clay to polymeric matrix. Differential scanning calorimetry (DSC) results indicated that the crystallization temperatures of samples are significantly higher than that of virgin PE. Moderate thermal stability enhancement of in situ polymerized nanocomposites was confirmed using thermogravimetric analysis (TGA).The storage modulus, Young's modulus and tensile strength of prepared samples were increased where the toughness was declined slightly. It seems that good dispersion and exfoliation of clay during polymerization should be responsible to get more effective reinforcing properties for clay in this method comparing to melt blending method for preparation of polyethylene nanocomposites.
AB - This paper is devoted to investigation of morphological and physical-mechanical properties of polyethylene (PE)/clay nanocomposites prepared via in situ polymerization method using bi-supported Ziegler-Natta catalyst. Bentonite type clay and MgCl2 (ethoxide type) were used as the support of TiCl4. Catalyst support and polymerization process have been done in slurry phase using Triisobutylaluminum as the co-catalyst. The microstructure of the nanocomposites was examined by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD and TEM indicated that almost fully exfoliated PE/clay nanocomposites were produced successfully using this method. According to permeability measurements, it was found that oxygen permeability values of the nanocomposite samples prepared with in situ polymerization method were dropped more than 200% introducing only 1 wt% clay to polymeric matrix. Differential scanning calorimetry (DSC) results indicated that the crystallization temperatures of samples are significantly higher than that of virgin PE. Moderate thermal stability enhancement of in situ polymerized nanocomposites was confirmed using thermogravimetric analysis (TGA).The storage modulus, Young's modulus and tensile strength of prepared samples were increased where the toughness was declined slightly. It seems that good dispersion and exfoliation of clay during polymerization should be responsible to get more effective reinforcing properties for clay in this method comparing to melt blending method for preparation of polyethylene nanocomposites.
KW - In situ polymerization (C)
KW - Mechanical property (E)
KW - Nanocomposite (B)
UR - http://www.scopus.com/inward/record.url?scp=67349104998&partnerID=8YFLogxK
U2 - 10.1016/j.matdes.2008.11.019
DO - 10.1016/j.matdes.2008.11.019
M3 - Article
AN - SCOPUS:67349104998
SN - 0264-1275
VL - 30
SP - 2309
EP - 2315
JO - Materials and Design
JF - Materials and Design
IS - 7
ER -